
Fuel Polishing for Generator Tanks
Fuel polishing means pumping the diesel out of a tank, filtering out water and sediment, and putting it back clean. It is how a set that has been standing for a long time is given fuel it can trust.
It is usually done after a fuel sample fails, or as part of a plan for a tank that seldom gets turned over.
- Why diesel ages
- Water and biodiesel content
- Bund rule (England)
- Usually 110% of the tank, with exemptions
- Applies to
- Oil over 200 litres at a business
Why stored diesel goes wrong
Road diesel in the UK is made to BS EN 590, which allows up to 7% FAME, the biodiesel part of the blend. FAME takes up water more readily than mineral diesel, and water in a tank is what bacteria and fungi need to grow.
The growth, often called diesel bug, forms a sludge where fuel and water meet. When the set starts and draws fuel hard, that sludge can be pulled into the filters and starve the engine. A tank that is rarely emptied, which describes most standby tanks, gives it plenty of time.
How polishing is done
Methods differ between firms, but the work usually follows the same broad order. Ask your engineer to explain theirs.
- Sample and test the fuel to see whether it needs cleaning at all.
- Drain off free water from the base of the tank.
- Circulate the fuel through filtration and water separation until it runs clean.
- Treat the fuel if the engineer recommends it.
- Retest and give you the results in writing.
Some sites fit a polishing unit to the tank so the fuel is cleaned on a timer. Whether that is worth it depends on how much fuel you hold and how critical the set is.
The tank itself: bunds and the law
In England, oil stored above ground at a business in a container over 200 litres usually needs secondary containment, such as a bund holding 110% of the tank. There are exemptions, for example some tanks inside a building that would hold a leak (Control of Pollution (Oil Storage) (England) Regulations 2001).
Scotland has its own rules, set by SEPA. Fuel stored on farms in England follows the agricultural fuel oil rules. Polishing is a good moment to have the engineer look at the bund too, because a full bund of rainwater is not doing its job.
When to ask for it
You may find the question comes up in one of a few ways. A service engineer flags dark or cloudy fuel. A set starts, runs briefly, then stops. Filters block far sooner than they should. Or the tank has simply sat full for years with no record of a test.
If none of those apply, ask for a fuel sample at the next service. It is a small job and it tells you whether polishing is needed.
How the job gets done
Tell us about the tank
Where it is, roughly how much it holds and what it feeds.
Access checked
The engineer confirms they can reach the tank fill and draw points with their rig.
Sample first
The fuel is tested so you only pay for cleaning it if it needs it.
Clean and retest
The fuel is polished and you receive the before and after results.
Fuel polishing: questions
What is fuel polishing?
Circulating stored diesel through filters and water separators to remove water, sludge and sediment, then returning it to the tank clean.
Why does my generator fuel go bad?
Diesel to BS EN 590 can contain up to 7% biodiesel (FAME), which takes up water. Water at the base of a tank lets microbes grow, and the sludge they make can block filters.
Does my tank need a bund?
Usually, in England. In England, oil stored above ground at a business in a container over 200 litres usually needs secondary containment, such as a bund holding 110% of the tank. There are exemptions, for example some tanks inside a building that would hold a leak (Control of Pollution (Oil Storage) (England) Regulations 2001). Scotland has its own rules (SEPA), and farms in England follow the agricultural fuel oil rules.
Can the set stay in service while the fuel is polished?
Often it can, but ask the engineer. It depends on the method and whether the tank has to be isolated.
How often does fuel need polishing?
There is no set interval. A yearly fuel sample at service time tells you whether it is needed.
Ask for a quote for your generator
We look for one service engineer who works in your area and tell you who they are before any of your details go to them. You pay nothing for this.
- You tell us where the set is and what it needs.
- We name an engineer who covers your site.
- You say yes or no before your details are passed on.
- They quote in writing, directly to you.
Thank you. Your request is with us.
We will be in touch by email or phone with the name of a service engineer who covers your site. Your details go to them only if you agree, and the price comes from them in writing. We send no marketing.